1. <track id="icaup"><div id="icaup"></div></track>
    2. <menuitem id="icaup"></menuitem>
    3. <menuitem id="icaup"></menuitem>

      <tbody id="icaup"><div id="icaup"></div></tbody>
      <track id="icaup"><span id="icaup"></span></track>
      Contact

      What Are The Standards Of The Qualified Auto Duct Line II?

      Auto duct line has become an indispensable product in many industries, even irreplaceable in some industrial process, so the qualified auto duct line II is also important. The following are the standards offered by a manufacturer.

      1. Clean the joint of the auto duct of the system: clean all the joints of the auto duct, fittings, components and the static pressure box of the clean system which must be tightly sealed; clean the inner surface of the air duct of the clean system which must be smooth and smooth. It is strictly prohibited to use the method of horizontal joint and pipe inner installation reinforcement or the method of using convex edge reinforcement.

      2. The auto duct shall be tightly closed, evenly spaced and free of holes, half-bite holes, expansion cracks or other defects. The vertical seam of the straight pipe is staggered; Make sure that the appearance of the auto duct, the bending angle is flat and straight, the arc is even, the two ends are parallel without obvious warping angle, and the surface is concave and convex no more than 10mm. The auto duct and flange are firmly connected, and the turnup is basically flat. The width is not less than 6mm, and the turnup is close to the flanges.

      3. The space of the flange of the air duct, the hole spacing of bolts and rivets of the flange should not be more than 150mm with firm welding. There is no screw hole at the welding seam. As to the auto duct of stainless steel plate, aluminum plate and composite steel plate, the surface of the stainless steel plate and aluminum plate auto duct should not have an obvious mark, scratch, cavity and other defects; While composite steel plate, auto duct surface should not have any damage.

      If the quality of the auto duct line II has been tested, the correct maintenance method of the later auto duct line needs to be understood so as to maintain its performance and prolong the use time.
      Related News
      • New Riveting Technology of Riveting Machine Manufacturers

        New Riveting Technology of Riveting Machine Manufacturers

        July 30, 2018The press ring of the manufacturer of the riveting machine first presses down the riveting material by a downward movement, in order to prevent the material flowing into the die under the force of the...view
      • Cautions in the Use of Electric Shearing Machine

        Cautions in the Use of Electric Shearing Machine

        April 11, 2019An electric shearing machine is a machine that cuts sheets in a reciprocating linear motion between one blade and another. By means of moving the upper blade and fixed lower blade, reasonable blade cl...view
      • What Are The Advantages Of One-drag Snap Lock Duct Machine?

        What Are The Advantages Of One-drag Snap Lock Duct Machine?

        June 27, 2019Air duct machine is also called air conditioning air duct machine or air duct machine air conditioning. It uses concealed installation like household central air conditioning, and has no difference in...view
      • Introduction of Rectangular Pipe

        Introduction of Rectangular Pipe

        June 27, 2019In the past, the sawing machine was used to process the whole process, which required 11 people to complete. The labor intensity was high. There were still errors in manual measurement, and a lot of w...view
      • Introduction of Corner Code Assembly Machine

        Introduction of Corner Code Assembly Machine

        June 27, 2019Corner code assembly machine is mainly used for flange corner code assembly at both ends of rectangular common plate square pipe. It is the supporting equipment of rectangular square pipe production l...view
      • Cnc Angle Steel Flange Production Line

        Cnc Angle Steel Flange Production Line

        June 27, 2019The cnc angle steel flange production line consists of eight parts. Horizontal feeding part, turnover feeding part, longitudinal feeding path part, feeding trolley, main engine part (one typing unit, ...view
        1. <track id="icaup"><div id="icaup"></div></track>
        2. <menuitem id="icaup"></menuitem>
        3. <menuitem id="icaup"></menuitem>

          <tbody id="icaup"><div id="icaup"></div></tbody>
          <track id="icaup"><span id="icaup"></span></track>
          一级a做视频免费观看,欧美高清在线精品一区,116美女写真午夜一级,欧美日韩无码有码在线,中文字幕5566最新网站,偷柏自拍亚洲不卡综合在线