1. <track id="icaup"><div id="icaup"></div></track>
    2. <menuitem id="icaup"></menuitem>
    3. <menuitem id="icaup"></menuitem>

      <tbody id="icaup"><div id="icaup"></div></tbody>
      <track id="icaup"><span id="icaup"></span></track>
      Contact

      Prevention And Cure Of Twice Crochet Breaking Of Lock Seam Machine

      Breaking thread is the most common fault in sewing. Unqualified sewing quality, inappropriate machine adjustment, sharp edges in threaded parts, problems in operation methods, inadequate cooling of needles, etc., will lead to wire breakage. When you are sewing uneven thickness products with lock seam machine and meeting the problem of breaking thread, in addition to considering and analyzing the above reasons one by one, attention should also be paid to the broken thread caused by two hooks. In the sewing equipment, the transmission ratio of the upper shaft and the spindle of the lock seam machine is 1:2 because of the need of distributing the action cycle in the design. The upper axle rotates one week and the spindle rotates two weeks.

      If the spindle hooks the surface thread every time, which means, once the machine needles the material and twice the spindle hooks, it will conflict with the drawing and placing of the surface thread, resulting in the phenomenon that the sewing line is broken. This may occur when you are sewing uneven thickness seams. The reason has to start with the formation process of lock-type trace.

      Formation of Lock-type Track

      Lock stitches are made up of interwoven surface and bottom stitches in sewing materials. When the sewing machine is working, the needle lead surface thread passes through the sewing material and rises up after reaching the lower limit position. Because of the friction between the stitching material and the stitching thread, the surface thread can not be lifted synchronously by random needle, but remains under the stitching material and expanded to both sides of the machine needle under the action of elasticity to form a ring. Then, the spindle tip reaches the machine needle in the process of motion, passes through the surface loop, and expands the hooked loop in the process of continuous rotation. When it reaches its own radius, it "jumps" over the enlarged loop like a rope skip. The next step is to take the pick-up rod off and feed dog so that these movements have enough time. The shuttle still rotates at the original speed for a week, but no longer hooks, only idles for a circle. Due to the closing effect of the take-up rod, the area loop which is enlarged and "leaped" by the shuttle quickly shrinks until the bottom line drawn from the center of the shuttle is pulled into the sewing material to form an interweaving. When the needle reaches the upper limit position and goes down again, the sewing machine starts again, and repeats the above-mentioned action process, thus forming continuous and regular lock stitches on the sewing material.

      Welcome to order lock seam machine of Blackma.
      Related News
      • The Principle of the Riveting Machine

        The Principle of the Riveting Machine

        July 30, 2018The riveting machine is easy to use, efficient and easy to operate. It is widely accepted by manufacturers and customers.According to the structure type, the riveting machine can be divided into many ...view
      • Introduction of Corner Code Assembly Machine

        Introduction of Corner Code Assembly Machine

        June 27, 2019Corner code assembly machine is mainly used for flange corner code assembly at both ends of rectangular common plate square pipe. It is the supporting equipment of rectangular square pipe production l...view
      • Overview of the classification of shearing machine

        Overview of the classification of shearing machine

        July 5, 2018Use and classification of shearing machineThe shearing machine is mainly used in cutting the straight edge of various sizes of sheet metal and is widely used in cars, planes, steel rolling, tractors, ...view
      • How to Inject Lubricating Oil Into Shearing Machine

        How to Inject Lubricating Oil Into Shearing Machine

        July 30, 2018It must be safe and reliable in order to work without problems for the machine safety. We need to scrub and maintain them regularly when we maintain machine tools. It needs ten minutes to do all these...view
      • Structure and Working Principle of Duct Beader Machine

        Structure and Working Principle of Duct Beader Machine

        July 25, 2019When duct beader machine bends the pipes, the rocker arm bears circumferential force and resistance moment. The rocker arm's return position is driven by the rocker arm driving device, and the return ...view
      • The Seven Advantages Of Flange Forming Machine

        The Seven Advantages Of Flange Forming Machine

        July 5, 2018Flange forming machine is able to produce excellent flanges quickly and efficiently because of its many characteristics, mainly 7 aspects. 1. Small size and Lightweight The flange forming machine adop...view
        1. <track id="icaup"><div id="icaup"></div></track>
        2. <menuitem id="icaup"></menuitem>
        3. <menuitem id="icaup"></menuitem>

          <tbody id="icaup"><div id="icaup"></div></tbody>
          <track id="icaup"><span id="icaup"></span></track>
          一级a做视频免费观看,欧美高清在线精品一区,116美女写真午夜一级,欧美日韩无码有码在线,中文字幕5566最新网站,偷柏自拍亚洲不卡综合在线